Home > work out > Life and health

Repair methods of fishing rods and precautions for fitting joints

A fishing rod will come into contact with water during use, and it will wear out over time. After a certain period of time, it will become disconnected. If you want to keep using a rod that is easy to use and don’t want to throw it away, it must be repaired. At present, I have three ways to repair it, and I will share them with you without reservation. If it was helpful to you, please give it a thumbs up.

Materials: 502 glue, Dali horse thread, horse-drawn tape

Tools: scissors, vernier calipers, etc.

Repair methods of fishing rods and precautions for fitting joints

1. Glue repair method

If the rod is not much worn, you can use 502 glue to repair it. Fishing gear is sold. The method is simple, has few steps, and is easy to repair. Prepare 502 glue and fix all the problems. When the disconnected part is taken out, you can see the anti-lock groove end. About 4 to 5 cm has been polished. It has become more worn after use. Wipe it clean with a dry paper towel. Cut a small hole on the head of the prepared 502. Try dripping it first, do not pour out a large amount of glue at once, and then lightly apply 502 glue on the anti-lock groove, slowly rotate the pole, and let the 502 glue cover the pole in a circle, and wait until it dries. After it is completely dry, wrap it with fine sandpaper and turn it for a few times, then reinstall it to see if it has been repaired. If it is still loose, you can repeat it again. Until it is repaired,

Repair methods of fishing rods and precautions for fitting joints

Repair methods of fishing rods and precautions for fitting joints

< p align="center">Repair methods of fishing rods and precautions for fitting joints

Repair methods of fishing rods and precautions for fitting joints

2. How to repair with tape

In addition to 502 repair, you can also Use horse-drawn tape (used by electronics factories to wind the lower voltage regulator), take out the disjointed rod section, and wrap a second layer of tape around the disjointed anti-lock groove, the width of which is the width of the anti-lock groove. After wrapping, Try to install it and see if it can’t be pulled out.

Repair methods of fishing rods and precautions for fitting joints

< img data-action="zoom" alt="Fishing rod repair methods and matters needing attention in fitting joints" src="https://img.111diy.com/timthumb.php?src=/d/file/fujian/e50b357c562a1ce2c5208d247b80a596.jpeg" />< /p>

Repair methods of fishing rods and precautions for fitting joints

3. Things to note when assembling joints

If the joint is out of joint and you don’t want to repair it, then just install the joint directly. You can directly Go to the fishing gear store to get the joints. If the fishing gear cannot be matched, you can also go directly to the manufacturer to get the joints. For some poles produced in the early years or if you cannot find the joints from the manufacturer, you can directly install the joints and take out the rod with the joints you want. For example, if the fourth section is out of joint, use a vernier caliper to measure the outer diameter of the fifth anti-lock groove and record it, for example, 3mm. Then measure the inner diameter of the third section, record it, 4.8mm, and then measure the rod section. length, then go to the store to buy 2.8mm.The anti-lock groove is a 5m pole section, you can just install it directly after buying it. If you are not sure, you can ask the store

Repair methods of fishing rods and precautions for fitting joints

Repair methods of fishing rods and precautions for fitting joints

Repair methods of fishing rods and precautions for fitting joints

4. How to repair a broken rod

When fishing, sometimes big objects are caught, the operation technique is wrong or careless, causing the rod to explode. Use it smoothly. Not willing to throw it away, the fishermen started repairing it. How to modify the explosive rod? Prepare 502 glue, Dali Ma, and a thinner one. Take out the two damaged sections and wrap them lightly with tape to prevent them from becoming short after repair in the future. If it doesn't fit, then wrap the prepared Dali horse along the damaged area in a layer. The length should not be too large. Wrap it all the way past the damage by 1cm. After wrapping, take out the inner section and drip 502. glue on the Dali horse thread. It should not be too much. Turn the pole slowly so that there is glue all over the body, but do not let the glue enter the wall of the pole, otherwise it will not be used even after repairing it.

Repair methods of fishing rods and precautions for fitting joints

Repair methods of fishing rods and precautions for fitting joints

Repair methods of fishing rods and precautions for fitting joints

To summarize, when using Be careful to use 502 glue when repairing to prevent the glue from flowing to other places. Be careful to repair the pole away from children to prevent the glue from hurting children.

Pay attention to the thickness when repairing the tape. If it is too thick, the length of the pole will not be enough. It also affects the tonality.

When assembling joints, measure the diameter several times. If you don’t understand, ask more questions. Pay attention to the softness and hardness of the pole and find the corresponding hardness of the rod joint.

Wish you all the best Anglers are big crucian carp and big carp.