Do you know the birth process of a pure handmade horse leather belt?

Author: lamlam, WeChat: leewinglam0511 The birth process of a handmade horse rein leather belt went through thirty steps and eight hours. The length is customized for the customer, with only two exclusive holes for winter and summer use, and finally the customers exclusive name is ironed on. Such an exclusive horse-bridle leather belt is born for buyers and born for quality.

Customized for customers before A London-colored bridle leather belt, recording the production steps. Share: 1. Everyone’s waist and dressing habits are different, so everyone’s belt length is different. Therefore, at the beginning, you need to cut out the required length and the shape of the belt tail you like according to your personal preference.

2. Use Use a leather trimmer to gradually bevel the belt head.

3. Start For edge sealing of the belt, first wet the edge of the belt with clean water.

4. Use Use a 2mm spacing edger to press out the decorative line. First lightly press a mark, then slowly increase the intensity and press several times more.

5. Press the effect of the decorative line.

6. Use a No. 3 or larger edger to trim the edges.

7. The flesh side of the belt also needs to be trimmed.

8. After trimming the edges, Use a cotton swab to evenly apply water on the edge of the leather in sections. The length of the water should be between 10 and 15 centimeters, and then polish this section with a wooden stick before continuing to the next section.

9. Use a wooden stick to polish back and forth before the water dries. Please be careful not to squeeze the edges of the leather and cause deformation when polishing.

10. Polish until it is shiny as shown in the picture.

11. Use a cotton swab to apply an appropriate amount of leather edge sealing liquid, be careful not to wipe out the border, and wait for the edge sealing liquid to dry naturally. (Don't worry, we use This oneThe edge sealing liquid dries relatively quickly. )

12. Use the finer side of the sand bar to sand. This step is mainly to smooth out some pits on the edge.

13. When sanding strips of leather, care and patience are particularly important here.

14. Again Apply clean water and polish with a wooden stick until it looks like the picture below.

15. Again Apply edge sealing liquid and wait for it to dry naturally.

16. Leather After the edge sealing fluid is dry, sand it with 400-grit sandpaper. Be careful + patient, be careful + be patient, be careful + be patient, say important things three times!

17. Again Apply edge sealing liquid.

18. At this time, the effect is as shown in the picture, and there will be some small pits.

Polish with 19.800 grit sandpaper.

20. The effect after applying the edge sealing liquid is as shown in the picture after drying. At this time The edges are already very smooth.

< /p>21. Start making the belt ears. Cut a piece of leather with a width of 1.3 cm. The length is determined according to the thickness of the belt. Follow the previous steps to press out the decorative line.

22. Use the No. 2 edger to trim the belt ears, and then follow the instructions above The edge sealing method is used for edge sealing.

23. Use an oval punch (4.5*23) to punch a hole in the belt head. This hole is used to install the pin of the belt buckle.

24. Dig out two grooves according to the width and thickness of the belt lug.

25. Use Use a thinning knife to thin both sides of the belt lug.

26. Use Make four holes at both ends of the round chop.

27. Use Cross stitch the two sides with round wax thread.

28. Belt The head requires sutures, so the holes need to be pre-punched. Here, we’re using 3.85mm pitch leather choppers for punching.

29. The belt head and belt ears are installed on the belt, and the belt is bent, glued and sewn.

30. Iron Apply the customers exclusive lettering mold, use a suitable round punch to punch the belt holes, and select the round punch according to the size of the pin buckle.

31. Schematic diagram of the finished product.

32. Final makeup photo.

I have always believed that handmade does not mean It must be rougher than the one produced by the factory assembly line. Its just that the manual output is low and it is not well known by the public.

Belt