Home > Paper art encyclopedia > Paper sculpture tutorial

How to make handmade paper carvings for lampshade and lamp bucket installation

How to make handmade paper carvings for lampshade and lamp bucket installation

Tools and materials required for DIY lamp bucket installation special folding method:

paper 1 set of lamp drawings, 1 set of paper lamp accessories, 10ml of PVC special glue, 1 roll of paper tape,

Illustration of the special folding method for DIY lamp bucket installation:

DIY lamp bucket installation special folding method step 1:

How to make handmade paper carvings for lampshade and lamp bucket installation

Paper cutting material package (the material package contains all required items) (the light bulb is fragile and you need to buy it yourself. 25W white porcelain light bulb, warm color is good)

DIY lamp bucket installation special folding method step 2:

How to make handmade paper carvings for lampshade and lamp bucket installation

2 pieces of protective film need to be taken out from the paper tube.

Step 3 of the special folding method for DIY lamp bucket installation:

How to make handmade paper carvings for lampshade and lamp bucket installation

There are two membranes. Place the engraved drawing in the middle. The drawing and the membrane are centered up and down, and aligned with either side of the left and right sides (attached to the smooth side of the membrane, with the rough side facing outward! ) The effect is as shown in the picture

Step 4 of the special folding method for DIY lamp bucket installation:

How to make handmade paper carvings for lampshade and lamp bucket installation

Key point: Use glue to fix the film and the drawing. Only one end can be fixed. This is very important (the picture is aligned to the left). Because the drawing will move during the rolling process, you only need to Just fix it on one side - don't forget: a small amount of glue is enough, too much glue will soak the drawing and the glue will be black when it dries! The effect is as shown in the picture

Step 5 of the special folding method for DIY lamp bucket installation:

How to make handmade paper carvings for lampshade and lamp bucket installation

Press on another piece of film and fix it with glue, starting with the fixed end

DIY lamp bucket installation special folding method step 6:

How to make handmade paper carvings for lampshade and lamp bucket installation

Rendering: The sandwich drawing only needs to be glued to one end. 😉Don’t forget: only one end needs to be glued. The effect is as shown

Step 7 of the special folding method for DIY lamp bucket installation:

How to make handmade paper carvings for lampshade and lamp bucket installation

The lamp surface has been completed (as shown in the picture)😉Note: "The glue is not an instant-drying glue and will be completely solid after 10 minutes. Minor debugging can be done during this time. 》

Step 8 of the special folding method for DIY lamp bucket installation:

How to make handmade paper carvings for lampshade and lamp bucket installation

Take out the light stand from the material box (there are two light stands, upper and lower, the picture is the light stand below) apply glue on the outside of the light stand and leave it aside to dry for 10 minutes , and proceed to the next step at the same time. 😊Alert: Just the right amount of glue is enough!

Step 9 of the special folding method for DIY lamp bucket installation:

How to make handmade paper carvings for lampshade and lamp bucket installation

*Apply glue to the lower and upper parts of the lamp surface at the same time, just parallel to the edge of the drawing* Apply a small amount of glue and leave it for 10 minutes. The effect is as shown

Step 10 of the special folding method for DIY lamp bucket installation:

How to make handmade paper carvings for lampshade and lamp bucket installation

After 10 minutes, roll the glued lamp holder onto the glued lamp surface (start from the spread out end) The effect is as shown in the picture

DIY lamp bucket installation special folding method step 11:

How to make handmade paper carvings for lampshade and lamp bucket installation

After gluing, as shown in the picture, then adjust the position of the light stand appropriately (the light stand is aligned with the edge of the drawing), the effect is as shown in the picture

Step 12 of the special folding method for DIY lamp bucket installation:

How to make handmade paper carvings for lampshade and lamp bucket installation

Repeat the above step, put the upper lamp holder into the glue area of ??the lamp surface (upper part), and glue it! And fine-tune the position, leave it for 5 minutes after debugging, the effect is as shown below

DIY lamp bucket installation special folding method step 13:

How to make handmade paper carvings for lampshade and lamp bucket installation

After the light holder is installed and fixed, glue the mouth and surface together, one layer at a time, with just a small amount of glue

Step 14 of the special folding method for DIY lamp bucket installation:

How to make handmade paper carvings for lampshade and lamp bucket installation

Step 15 of the special folding method for DIY lamp bucket installation:

How to make handmade paper carvings for lampshade and lamp bucket installation

The lamp bucket is completed! !

DIY lamp bucket installation special folding method step 16:

How to make handmade paper carvings for lampshade and lamp bucket installation

Use a pen to draw a round hole on the back (the round hole is carved according to the size of the rubber ring. You can first draw a circle of about 5 mm, and if it is not enough, then gradually engrave it larger)& #128521;Alert: The position of the hole must be higher than the position of the light stand!

DIY lamp bucket installation special folding method step 17:

How to make handmade paper carvings for lampshade and lamp bucket installation

When making the first cut of the hole, the force of the carving knife should be stronger. 😉Alert: When making the hole, you must be slower. Make the hole according to the size of the rubber ring! Watch out paddlers!

DIY lamp bucket installation special folding method step 18:

How to make handmade paper carvings for lampshade and lamp bucket installation

The picture shows the carved wire holes

DIY lamp bucket installation special folding method step 19:

How to make handmade paper carvings for lampshade and lamp bucket installation

Adjust the hole pattern according to the size of the rubber ring and then install the rubber ring

Step 20 of the special folding method for DIY lamp bucket installation:

How to make handmade paper carvings for lampshade and lamp bucket installation

Install the line😆Alert: After the line is put into the rubber ring, the line head still needs to pass through the line card. The line needs to pass through the small hole next to the line card, as shown in the rendering

DIY lamp bucket installation special folding method step 21:

How to make handmade paper carvings for lampshade and lamp bucket installation

Insert the wires into any small holes on both sides of the lamp head 😇 Warning: The lamp head has "no positive and negative poles and automatically fixes the wires"

DIY lamp bucket installation special folding method step 22:

How to make handmade paper carvings for lampshade and lamp bucket installation

After the cable is installed, stick the cable card on the lamp head

DIY lamp bucket installation special folding method step 23:

How to make handmade paper carvings for lampshade and lamp bucket installation

Place the lamp head into the lamp stand and use the lamp head clamp to fix the lamp head on the lamp stand

DIY lamp bucket installation special folding method step 24:

How to make handmade paper carvings for lampshade and lamp bucket installation

Due to the fragile transportation problem, the bulb needs to be purchased by yourself. Note: Only white porcelain lamps can be used for the adjustment switch. We recommend 25W (about 2 yuan)

DIY lamp bucket installation special folding method step 25:

How to make handmade paper carvings for lampshade and lamp bucket installation

Install the lights, plug in the power, and arrange the poss

DIY lamp bucket installation special folding method step 26:

How to make handmade paper carvings for lampshade and lamp bucket installation

Finally blossomed and bore fruit. As the saying goes: If you want to get a good thing, it takes time! 😄😄😉

DIY lamp bucket installation special folding method step 27:

How to make handmade paper carvings for lampshade and lamp bucket installation

The hard work is shown without any spare effort

DIY lamp bucket installation special folding method step 28:

How to make handmade paper carvings for lampshade and lamp bucket installation

A deep sense of pride

DIY lamp bucket installation special folding method step 29:

How to make handmade paper carvings for lampshade and lamp bucket installation

Actually, they are all very simple and everyone can understand them, but I was afraid of what might happen. After all, it took me so long to start carving, so I came up with this tutorial!

DIY tips:

The key point is the location of the glue (only one end is glued) and the amount of glue should not be too much. All places where glue is used need to be left for 10 minutes for bonding. The bonding effect will be better! After all, it is the last step before the finished product. Slow down and don’t be in a hurry when sealing the lamp tube