Author: finder handmade
Leather goods Taobao store: https://s.click .taobao.com/b2e1SOw uses the textured soft vegetable tanned Mbox from the Italian Badalassi Carlo leather factory, which is burnt tea and brown. It is matched with a single and double buckle card holder version. It is multi-functional, can accommodate cards and change, and is diverse. Main materials: about 2 feet of vegetable tanned leather, about 10 meters of twine, a small amount of glue, three sets of snap buttons, 240/400/1000/2000 sandpaper, a small amount of edge sealing fluid. Required tools: 3/4mm2+8 set of French choppers, A pair of flat-nose pliers, a small novice edger, one 3/5 large beetle, a set of four-button punching tools, an NT triangular grinding tool, a spacing gauge, and a pattern finder. Steps for making handmade leather goods:
The leather is Mbox focused The brown/brown 2mm thick product is pictured first. Here, the four-button buckle surface is exposed outside. If you need to put it inside, the specific production is given below.
Single button double The main part of the buckle is similar, but the shape of the lid is different. It is more natural to match one button or two buttons.
There are two internal An accordion compartment, which can hold multiple cards and change, is highly functional.
With A back card position so that the basic structure is clear.
First cut the material according to the pattern, and the pattern is certain Search finder handmade leather goods, mainly Japanese-style styles that require single-layer edge sealing should be edge-sealed in advance, such as the upper and lower edges of the organ, the arc on the outer skin, the upper and lower edges of the middle spacer leather, and the upper and lower edges of the back card. And single-layer bends. These should be done at the beginning.
Adhere the back clip to the outer skin according to the adhesive positioning points on the pattern, and clamp both sides with flat-nose pliers. Use flat-nose pliers to make the skin stick better It is strong, but of course it may leave some marks. Just pinch the edge of the leather a little and it can be dealt with in the future production.
Adhere the front and rear organs and the middle spacer. The pasting position can be roughened with coarse sandpaper to make the pasting easier. Solid.
Previous The two organs at the back
Sewing completed
When sewing, pay attention to wrapping the head twice, and the suture should be sewn to the end as much as possible to effectively avoid the use of edge sealing. During the process, the two ends were torn apart due to lack of restraint.
After sewing, seal the edges. The three layers here are about 6mm thick, and I used the Da Chong No. 5 edge trimmer.
Note: Please refer to the edge sealing method for more details. For details, please refer to the detailed tutorial on the website. What is easy to make mistakes is , many people will reverse the order of trimming and polishing. They should polish it flat first, then roll up the leather edge, and then use an edge cutter to trim off all the rolled leather edges. Then proceed to the subsequent edge sealing steps.
Paste in the next step Before sewing, you must first install the four-button buckle. Here you can trace the position according to the positioning points on the pattern when cutting the material.
After installing the four-button buckle, stick the front organ to the outer skin. Be careful to use flat-nose pliers on the leather edge. Clamp.
Polish the leather edge and then cut it. Because the bottom surface is uneven, you must make it flat before cutting. Of course, you can also Select double-sided chop.
< /p>After the left and right sides of the small organ are sewn, proceed to the next step of sewing the large organ. You can also use single-sided cutting or double-sided cutting, and it must also be padded flat.
It is safer to cut on both sides. It will be like cutting on one side for a while. It was thick and uneven, and it suddenly became crooked...
After cutting and cutting on both sides, stick it together. You can use some positioning pins here to help stick it.
Suture, it is also recommended that the suture should be wrapped twice at the head and tail.
Sewing of the cover: Because the buttons are exposed, Sew first and then install the buttons. If you want to hide the buttons inside the leather, you must first install the buckle surface on the bag cover and then glue and sew.
< img src="https://img.111diy.com/timthumb.php?src=/d/file/p/9fbbc6fa6fb2d3ab48640081c1cf6f79.jpg" alt="">
After the cover is sewn, trim the edges. The two layers here are 4mm. You can use the No. 3 edge trimmer. I prefer round edges. If you want to trim the bevel, you can use the large trimmer.
Overall seal As you finish, install the snap buttons and it’s done~
Another picture of the finished product. This bag does not need to be thinned at the edges, and only one thickness is used for the entire bag, so it is relatively easy to use materials. You can just buy a 2mm leather. Let’s get started~ Tips: Choose single- and double-sided chopping according to your proficiency. In addition, you must grind the edges before chopping. You must also grind the edges before cutting.
Card Pack
