Wallet vegetable tanned leather long wallet author: Wuzhi WUZHI, WeChat: 309790637 Detailed production steps Production tools: spacing gauge or edger, diamond chopper, hammer, cutting mat, needle, edge trimmer, frosting rod Production materials: plant Tanned leather pieces, bed surface agent, hand stitching, vegetable tanned leather rope, leather glue, glued cardboard
Production Notes: Due to the large number of skin patches, the skin patches are numbered in the tool diagram for ease of description. ①The leather flap is the shell of the long clip, and the ②③④⑤ and ⑥⑦⑧⑨ leather flaps are the clips on the left and right sides of the long clip respectively.
Handling card slots The upper edges of the skin flaps (②, ③, ④, ⑤, ⑥, ⑦, ⑧, ⑨) are smoothed with a sanding rod and then treated and polished with bed surface agent. *If the leather requires engraving, please complete it before stitching the card position. ◆Block stitching
Adhesion 1) Adjust the width of the spacing gauge to about 2mm, and use the spacing gauge to draw reference lines on the lower edges of the ③, ④, ⑦, and ⑧ skin panels.
2) Use The frosting rod rubs the edge of the ② leather piece near the bottom reference line to make the leather surface rough for bonding.
3) In ② Apply 3-4mm wide leather glue on the inside of the baseline at the bottom of the front of the leather patch and ③ on the bottom edge of the back of the leather patch.
4) Stack the ③ skin piece on ② Above the baseline of the skin patch, and glue the bottom. When gluing, pay attention to ③ The top of the skin patch just touches the ② convex position of the skin patch. ◆ Punch and suture
1) Place the glued leather piece horizontally on the cutting mat , use the diamond chopper to punch holes along the reference line in sequence. (For specific operation steps, see Lesson 2: Mobile phone hanging bag) Pay attention to keep the diamond chopper always perpendicular to the desktop.
2) Cut the corresponding length of suture, that is, 4 times the length of the stitch. , and thread the needle. 3) Use the correct hand sewing method to sew, pay attention to the backstitch and end the suture on the back of the card position. (Please refer to Lesson 2: Making a mobile phone hanging bag) ◆ Sew the second row of card positions
1) Continue in ② Apply leather glue to the bottom edge of the front side of the leather piece and the bottom edge of the back side of the ④ leather piece and glue them together. Pay attention to the alignment when gluing.
2) Punch a hole and sew, pay attention to the backstitch and end the suture at the back of the card position. ◆Sewing in the center line of the card position
1) Use a ruler to measure or find the midpoints of the upper edges of ②, ③, ④, and ⑤, and use a needle or awl to lightly tap them as marks.
2) ⑤ Align and stack the skin patches on ②, ③, and ④ to the corresponding positions. Press it lightly with one hand to fix it, and use a diamond chopper with the other hand to align the midpoint mark marked in the previous step, and drill holes at the corresponding position. POINT: When punching holes, make sure all parts of the leather are aligned and do not move or dislocate the leather.
3) Move the diamond cutter down and align it with the marked midpoint mark, and continue drilling until there are 10-12 holes on the midline.
4) Suture For the centerline hole, pay attention to backstitching and end the suture at the back of the card position.
5) Use End the suture with an electrocautery pen. 6) Use the same method to sew the leather clip on the other side (⑥⑦⑧⑨). ◆Sewn long clip shell
Before sewing the shell, apply bed agent to the middle part of the back of the leather piece ①, that is, between the slots on both sides, and polish it to make it smooth and smooth.
* Or glue the skin piece of appropriate size at the corresponding position. When gluing, pay attention to the alignment of the skin piece. ◆Draw the reference line
1) Put the spacing gauge close to the ruler and adjust it to 2mm distance, and tighten the screw cap to fix it.
2) Use a spacing gauge against the front edge of the ① skin graft, and draw a 2mm baseline along the edge inward. 3) Rotate the skin graft and draw a baseline on each edge. ◆gluing
1) Apply leather glue to the back bottom and both sides of the leather piece in the clip position, as well as the back edge of the leather piece ①. 2) Align the leather piece in the clip position to the corresponding position of the leather piece ① and glue it. After bonding, as follows: If you find any misaligned parts, you can gently tear the skin apart and re-glue it.
3) If it is loosened, continue to use the glue card to add leather glue to ensure that the leather clip and the shell are completely fit. 4) Glue another clip leather piece. ◆Punch
1) Use a diamond chopper to drill holes on the reference line on the front of the long clip shell. You can start from the leather card position or one of the corners of the long clip.
< img src="https://img.111diy.com/timthumb.php?src=/d/file/p/2403a8dfc2cce8e18c635243157a3356.jpg" alt="">
2) When the remaining 8cm is drilled, press the hole position from back to front. Pay attention to the diamond bevel teeth to be just right. Fall on the intersection point of the reference line of the corner of the skin piece. 3) If it is found that the hole position from the back to the front cannot match the previously drilled hole position, you can use a 2-tooth diamond chopper to drill holes in the middle part to adjust. It finally matches.
Sew the edge of the long clip shell and remember to backstitch.
Put the wire through the inside of the long clip and tie it with an electrocautery pen. ◆Process the edges
1) Use a sanding rod to polish each edge of the wallet until it is flat. At the same time, polish the four corners of the long clip to make it smooth. Smooth.
2) Use an edge trimmer dipped in bed surface agent to polish the edge of the long clip. (For details, please refer to Lesson 1: Making a Mouse Pad) Then it’s done blah blah blah!!!
Long clip
