Mens handbag making tutorial, basic making process of mens zipper handbag

Author: Flato, WeChat: k9999w11 This article records the simple process of a mens handbag (not a tutorial). It mainly introduces the production process of a mens handbag, the order of making parts, and the processing methods of several handbags. This handbag It’s not a haute couture, but the customer requested to increase the thickness of the handbag, so the process is simple and suitable for novices (with basic handicraftsLeather goods basic friends) made. There may be some irregularities in the production process, such as no drawings and no templates. This is just my personal habit. I just do it as I go. Except for the areas where drawings and templates are very much needed, I will draw pictures and make templates. , no other pictures are drawn, just cut the material according to experience, and leave the leather for cutting out in the later stage if you are not sure. Colleagues and perfectionists please spray lightly. 1. Large internal and external parts

First of all, face to face Cut out the lining. The dimensions here are 24cm*20cm for the dough and 23cm*20cm for the lining. The outer skin is 1cm longer than the lining, which is the reserve required for bending and sticking. Then make a semi-circular gap at each end of the center line of the lining to reserve space for the zipper.

These two pieces of leather All are precisely cut. After cutting, use No. 2 or No. 1 edge trimmer to chamfer the leather edge, iron the edge with an edge ironing device, and seal the edge with edge sealing liquid. This is the normal process for vegetable tanned leather.

Then the dough can be placed Set aside for use, turn over the inner skin, make it 3cm wide in the middle, and thin it, hereIt needs to be bent and bonded, so it must be thinned. I thinned it to about 5mm here. 2. Coin bag part 1. Coin bag zipper

Here I made a version with a rectangular size of 8cm*17cm to make a coin purse in the middle. You can also directly make 16cm*17cm and fold it in half, because in the end I also used 16*17cm and this square was not used.

Take a length of zipper 17cm, as the zipper of the coin bag, use vise to remove the zipper teeth from the beginning to the end. The following introduces a method commonly used by Hermès to deal with zippers.

First remove the teeth Fold the zipper cloth as shown above and stick it with glue.

Then turn the zipper over , fold the corners just glued over and glue them in place. In this way, the toothed part of the zipper forms a right angle. The zipper made in this way is more beautiful and stronger than the open one. The zipper on the other side is processed in the same way. After processing, install the top stop of the zipper. Restless. Be sure to pay attention here: don't stick it backwards when gluing it, and don't install it backwards when attaching the zipper. 2. Coin bag body

After the zippers on both sides are processed, they are directly glued to both sides of the coin bag. As you can see from the picture above, the two sides of the coin bag have been ironed and sealed. In the production of vegetable tanned leather, all exposed parts need to be edge-sealed, which I won’t go into details later. You can see on the side of the coin bag that I made a 4mm wide thinning. This is to facilitate the later application of glue, and the leather surface needs to be Cut off. After gluing, cut the sutures normally.

After sewing the thread, fold the coin bag in half and align the two zippers. After inserting the zipper puller, insert the bottom stop from the back and pinch it tightly with pliers. Apply glue to the inside of the empty areas on both sides of the coin bag and stick it. Coin bag The main model has come out. The desktop is very messy, please ignore it, and there is a cigarette in your hand, please ignore it if you are a minor. 3. Coin bag accordion pleats

Next, make the accordion pleats. Pattern making is required here. This is also based on experience. If the top side is long, cut 5.5 on both sides. cm, the middle straight part is 1cm. The short lower part is 2.5cm on both sides, and the middle straight part is 1cm. There is a width of 1cm in the upper and lower middle, which will be thinned out later.

As shown in the picture, the 1cm part in the middle is thinned to 0.5mm thickness, two pieces Groove the pleats (you don’t have to dig them), and glue on both sides and thin the width by 4mm. The two accordion pleats are processed in exactly the same way, and you can just copy the same on the other side. After processing, use the thinned one in the middle. Place, glue to the side of the coin bag.

As shown in the picture above, cut the seams after gluing, and the coin bag is completed. 3. The inner card position

There are two card slot sizes. The size of the upper two card slots is 19cm*4.7 cm. The next card position is 19cm*4.9cm.

After the silver surface is processed, you can cut the edges normally and iron and seal the edges.

The area on the lower side that needs sutures is thinned to a width of 5mm. Then sew to the top of the lining in sequence.

The card positioning effect is sewn on one side.

Sew the effect on both sides. It should be noted that the stitching In the place, you need to dig grooves and bury the threads on the back of the inner skin. Otherwise, when the outer skin is finally attached, the outer skin will leave stitches, which is ugly. There will be pictures later to show what it looks like after digging the trenches and sewing. The two sides are stuck After sewing, the card position is completed, and the following is the gluing part of the overall zipper, which should be the part that everyone is more concerned about. 4. The overall zipper part. As mentioned before, the customer of this handbag requires a width of 3cm to 3.5cm in thickness. I need to hold 15k in cash, so I widened the zipper with leather to ensure that the width of the zipper part is 3.2cm (3.5cm is too thick, and a single-layer zipper is ugly). When connecting a wide zipper, you need to use The technique of cutting is mentioned in my last thinning tutorial. After cutting, the thin part is used as the connecting part between the zipper and the bag body.The points are very straight, and the advantages of the cutting effect can be reflected here. The boundaries are clear and there is no fear of sticking. Friends who don’t understand cutting can refer to the link. http://www.pixiaojiang.com/topic/show/123 The overall zipper is sticky as shown in the picture above. There are a few points to explain. First: the ideal thickness of the broken part should be within 0.5mm. Second: Glue the lining with the lining in advance when gluing. Keep the zipper locked before gluing it, do not separate it. Third: When gluing, stick along the cut height difference line to the edge of the inner skin, so it will not be crooked. Fourth: Glue the three straight lines first and finally handle the bends. Fifth, use scissors to cut the skin a few times at the bend, then trim it into a triangle before gluing it on. If you glue the zipper directly here instead of the leather zipper in the picture, the method is similar: first: make sure it is locked and then glued. Second: There are several lines marking the width of the zipper. Choose one of them and glue it along the edge of the inner skin so that it will not be crooked. Third, glue the three sides straight first and then handle the bend. Make a pleat at the bend and glue it on. Fourth: Use yellow glue (all-purpose glue). 5. Overall suture part

Zipper After everything is glued, you can glue the outer skin. As shown in the picture, align one side and glue it first, then align the other side and glue it. After both sides of the outer skin are glued, open the entire zipper of the bag, and then we cut it from the inside to the outside. Its time to test your cutting skills. Make sure the cuts are vertical, penetrate directly, and make sure the cutting mark on the outer skin is a straight line.

That’s it. However, after cutting, cut both sides of the accordion pleats of the coin purse. The number of cuts of the accordion pleats must be calculated correctly, and there should not be too much error. After the accordion pleats are tied and cut, they can be glued to the inside of the bag, or not glued (I didn’t glue them here, just sewed them directly).

All cuts are done After that, it’s time to sew.

The final sewing effect. After the sewing is completed, the bag is finished, and there is no other follow-up processing. 6. Finished drawing

Go here to share the handmade leather goods skills in this issue It’s over. After all, it’s not a tutorial, it’s just a process. Moreover, this model is not high-end, and there are almost no skills in detail production. It is actually very simple. Therefore, if you still don’t understand anything, you can leave a message and interact. If you know anything, I hope you can. Everyone likes it. Salute.

Mens Handbags