After making so many horizontal short clips, some friends said it was not convenient to put them in their pockets. So the DIANA vertical short clip shared today is smaller and lighter, which may solve this pain point.
1. Use Use the cover as a reference to cut the crocodile tail. When cutting, be careful that the edge of the paper grid cannot fall on the gap between the crocodile scales. When aligning, spend some time moving the paper grid to avoid the gap, and try to find a suitable position before using the knife. At the same time, pay attention to the direction when cutting materials. We recommend cutting materials in the direction as shown in the picture, that is, "opening sideways."
2. After the crocodile leather material for the cover is cut out, in order to protect the skin For the high-gloss effect on the surface, we can stick a layer of plastic wrap on it for temporary protection. In fact, high-gloss crocodiles are not as fragile as we think, after all, is the best among amphibians.
3. Connect Next, use other parts of the drawing to trim the goatskin. This time I’m sharing the secret blue French goat. Leather friends who have the conditions can try to select parts with symmetrical and perfect textures for production.
4. Next we start Time to deal with the crocodile cover part. The purpose of using interlining to adhere the crocodile flesh surface is mainly to increase the strength of the gaps between scales and make the work more durable. Of course, one way is to only paste the gaps. In fact, it can be done as long as you think about it to achieve reinforcement. When fitting, you need to bend the stick. Use the bending wooden mold to assist, which can make the fit better.
5. After attaching the interlining, start aligning The goatskin on the inside of the cover is attached. Also use bent wooden molds for assistance. After attaching it, cut off the excess part.
6. After the transfer paper grid is After cutting the holes on the cover of the crocodile skin, start cutting at the holes.
7. Yes The cover part is pressed with decorative lines for the first time, which has a decorative effect and also enhances the adhesion between the cover leather. The temperature used here is about 200 degrees Celsius.
8. Yes The upper edge of the cover is stitched. The order of stitching or top oiling at this location can be reversed. You can sew first and then oil the top, or apply oil first and then stitch.
9. Yes Oil the top edge of the cover.
10. Knock Wire. Here we use two hammers operating at the same time, which is safer. You can also try it.
11. After the cover is processed, we start to process the structure of the inner grid. First, we deal with the card positions and transfer the information on the paper grid. Printed on the leather.
< /p>12. Tailoring the card position (this step may be controversial, after all, everyone’s approach is different. You can not do the precise cutting of the card position here first, but you can also do it later.)
13. Use a circle with a diameter of 2 Punch holes at both ends of the card position. Then mark the auxiliary lines on the flesh side of the card position for the next step of aligning the card bag with lining.
14. Prepare the interlining according to the drawing. The total length of the interlining is about 49cm. According to the drawing Form, fold one short and one long in an orderly manner, and the adhesive paper does not need to be torn apart yet.
< /p>15. Brush glue on the position on the lining cloth as shown in the picture, and also brush glue on the corresponding position on the flesh surface of the leather where the clamping position is. The glue will begin to appear semi-dry and the fit will begin. Fit step by step from bottom to top, using a ruler when appropriate.
16. Pressurize the decorative line for the card position. First, it is for aesthetics. The second is to increase the adhesion between the card bag and the leather. Because the glue we useThe viscosity will be reactivated during the secondary heating process, so the card bag will stick more tightly.
17. Tailor-made card slots (This step may be controversial, after all, everyone’s approach is different. You can not do the precise cutting of the card position here, but you can also do the precise cutting later.)
18. Glue the two sides of the card position and fit them together.
19. Put the card position paper Transfer the information on the grid to the card position. Pay attention to the cut holes at the end points. It is recommended to use round ones.
20. Start Start sewing on the inside of the clips on both sides, and remember to tap the thread.
Vertical short clip
