Sharing a method of making a three-fold handbag from the author Ban Diao Yanyu. There are many steps. If you are interested, please read below!
For me, this handbag has a little more components. Now I have numbered it based on the original model:
Judge the production method and follow the production method Made in different groups.
1. C3 card area
1. Unloading.
C3-a upper half upper left and right Three sides are rough cut, and the lower half is finely cut on 5 sides.
Roughly cut the material at the middle and lower clamping positions (C3-b to C3-g), finely cut the adhesive-backed nylon, and stick the adhesive-backed nylon along the fold line or fold line. The left and right and lower edges of the adhesive-backed nylon are larger than the clamping positions. The accuracy is 5mm.
Roughly cut the bottom fabric in area C, indent 5mm on each side of the adhesive-backed nylon, and stick it to the back of the bottom leather.
2. Finely cut the upper clamping position (C3-b to C3-f) and thin the upper edge
3. Fold the upper card position and lower the Card slot folded in half
4. Upper card position (C3-b Go to C3-f) Finely cut the edges on the left and right sides, leaving the bleeding bits on the left and right sides
The lower card position (C3-g) is not finely cut.
5. Thin the lower edge
6. Press the upper edge of the card position behind this side (C3-b to C3-g)
7. Paste the adhesive-backed nylon Mark the fitting position of the card position on the bottom leather
8. Place C3-a along the marked line Completely adheres to the base leather
9. Lower edge stitching
10. Fit the upper card position (C3-b) and sew the lower edge
11. Make the remaining 4 card slots in sequence (C3-c to C3-f) and 1 piece of lower clip (C3-g). The lower clip is only for fitting, without stitching.
12. Tailor a strip towards the inside of the handbag The long side
13. Cut the seams on the long side of the tailoring. The holes should be cut accurately where the card joints are connected, and do not leave any gaps.
14. Sewing the edge and pressing the line
15. Top oil
Okay!
2. C1, C2, A1
The production methods of these three areas are the same.
1. Rough cutting. Each area is composed of 1 piece of dough, 1 piece of bottom leather and 1 piece of adhesive nylon. The nylon adhesive backing is accurately cut into 5mm and attached to the back of the base leather.
2. Cut the edge of the lower half of the dough as shown in the figure
3. Thin the lower edge of the dough
4. Mark the dough fit on the land position and fit the dough
5. Finely cut the long side inward
6. Tailored long edges with cut seams
7. Sewing the edge and pressing the line oil on top
8. Paste C2 on C1
9. Paste C3 on C2
A1 spare.
3. A2, A3
1. Roughly cut the A2 material, indent the edge of the adhesive-backed nylon part by 5mm as shown in the picture, and fit it along the hem line.
2. Cut the upper edge of A2 and shave it Thin
3. Folding
4. Cut the lower half of A2, leaving the left and right bleeding spots
5. Press the folded edges
6. Thinning the bottom edge of A2
7. A2 is attached to A1
8. A2 bottom seam
9. A3 rough material cutting, backing The left and right sides of the rubber nylon are indented by 5mm and fit on the back of the A3 leather.
10. Mark the position and install the four-button buckle (Forgot to take a photo, draw a schematic diagram), stick a slightly larger piece of adhesive-backed nylon on the dark side of the snap button to reinforce it.
The magnetic buckle used here is better looking . But I'm afraid of degaussing...… used four-button buckle instead
11. Fold in half
12. Press the decorative line on the folded edge
13. A3 is pasted on A2
14. Cut the suture in the middle line (forgot Take a picture of the stitched line...), running through A2 and A3
4. Inner bag
1. Roughly cut three pieces of material: one for the inner and outer skins , a piece of soft and thin bran paper
2. Bonding the leather bran paper to the outer skin
3. Install four-button buckles on the inner and outer skins respectively two parts of
4. Internal and external batch matching
5. Tailoring
6. Organ pleats, fold the two pieces of skin Precision cutting and blanking after the materials are pasted
7. Cut the four sides of the accordion pleats and top Oil the edge seams and press decorative lines on all four sides
8. Make the cut holes on the large surface. Sew the edges that are not sewn with the accordion pleats and outer skin first.
9. Accordion pleats, not sewn with the outer skin Fit one side first and sew
10. The upper edge of the inner bag opening Oil
5. Overall combination
1. Outer skin and inner layer, one piece each of leather and leather bran paper
2. Fitting
3. Fine tailoring
4. A strip sewn between the middle and the inner bag suture
After sewing like this
5. Roughly cut a piece of outer skin. Attach a slightly larger adhesive nylon reinforcement to the position where the four-button buckle is installed, and install the four-button buckle (I forgot to take a photo, so I will draw a picture...)
6. Cut a piece of bulging inner skin Lining, indent 4mm on all sides.
I used a piece of leather bran paper at first, but after applying it I felt it was too hard, so I replaced it with 0.5 sheepskin and it worked. I only took photos of leather and bran paper.
7. Stick it on the outside of the outer skin and inner layer, Center, leave space on all sidesSeam space. (I forgot to take a photo again, so I held my forehead...)
Roughly cut the outer layer of the skin and stick it on the outermost layer. I think the skin made this time is a bit thick, so it bends when fitting. The position is slightly curved.
Drum and shape, then tailor the outer layer of skin along the edge of the inner layer.
8. Area A and Area C are posted on Inside skin
9. Cut area A along the edge of the outer skin , edge of area C
10. Fit the other side of the accordion pleat good
11. Cut the sutures on all four sides (I cut the stitches on both sides in order to ensure accurate cutting position and fit them well. On both sides, cut the stitches to the depth on each side. ...I don't know if there are any disadvantages...)
12. Press decorative lines inside and outside, and oil the top
Then it’s over!
